PSA AK103 plunges into the AKOU world!
Can rifle shoot when is 790F hot?
POI Shift!
600yds Delivery!
Support AKOU channel, shop at AKOU store!
Pages
Archives
- January 2023
- December 2022
- November 2022
- October 2022
- September 2022
- August 2022
- July 2022
- June 2022
- May 2022
- April 2022
- March 2022
- February 2022
- January 2022
- December 2021
- November 2021
- October 2021
- September 2021
- August 2021
- July 2021
- June 2021
- May 2021
- April 2021
- March 2021
- February 2021
- January 2021
- December 2020
- November 2020
- October 2020
- September 2020
- August 2020
- July 2020
- June 2020
- May 2020
- April 2020
- March 2020
- February 2020
- January 2020
- December 2019
- November 2019
- October 2019
- September 2019
- August 2019
- July 2019
- June 2019
- May 2019
- April 2019
- March 2019
- February 2019
- January 2019
- December 2018
- November 2018
- October 2018
- September 2018
- August 2018
- July 2018
- June 2018
- May 2018
- April 2018
- March 2018
- February 2018
- January 2018
- December 2017
- October 2017
- September 2017
- August 2017
- July 2017
- June 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- September 2016
- August 2016
- July 2016
- June 2016
- May 2016
- April 2016
- March 2016
- February 2016
- January 2016
- December 2015
- November 2015
- October 2015
- September 2015
- August 2015
- July 2015
- June 2015
- May 2015
- April 2015
- March 2015
- February 2015
- January 2015
- December 2014
- November 2014
- October 2014
- September 2014
- August 2014
- July 2014
- June 2014
- May 2014
- April 2014
- March 2014
- February 2014
Categories
- Uncategorized (595)
I have a PSA 103 SF with only 317 rounds fired so far. My question is, what is the correct firing pin protrusion? When I received the rifle I was experiencing a lot of light strikes, so they sent me two new firing pins. Now I am piercing primers with some ammo brands. Protrusion measured .067”. I shortened the firing pin (very little) and it is now .056” and haven’t had a chance to retest. What should the correct protrusion be? I have a GF3 that was purchased that same week, and while not as bad, is having the same issue. Any insight would be greatly appreciated!
If i remember this correctly it is between Min 1.40 mm and Max 1.52 mm. I would open warranty claim in your case.
Thanks for the reply Rob, love your channel and everything you do for the AK community! I’ll go to the range next week and try it again because it should be in spec now (1.42mm). This also helps me with the GF3, which by my measurements is Currently at (1.75mm). As an aside, both rifles have ran Barnual and wolf black box fine and were piercing golden tigger and Tula bad, at least one in 10. This would freeze the FP in the 103 almost every time! I like to tinker myself before I send it back, if it still does it next week, I’ll send it for warranty work. Thanks again!
Would you kindly share with me how you effectively mounted an OSS 7.62 suppressor on the AK-103? I have an AK-P coming in from PSA and would appreciate it if you would further elaborate/explain the route for suppressors.
So far I’ve been looking at: OSS HX-QD 7.62, OSS QD mount (was looking at their flash hider), and then some form of thread adapter?
Check your email Jan.
I’m picking up a PSA 103 soon, and would also like to know how you mounted the OSS Adapter! It looks like the Front sight is the threaded portion, so could there be an increased risk of baffle strikes?
OSS has 24mm muzzle device for their cans! Link: https://www.shop.akoperatorsunionlocal4774.com/searchquick-submit.sc?keywords=oss
I always check alignment with rod – so far, no issues on any of the PSA AKs.
Seems like my gas tube on my 103 is not going up all the way not against the stop is there a problem
Could you please email me pics? rob@ak4774.com